View source for Surface Mount Assembly for SimpleBot Shield

= Surface Mount Assembly =

The SimpleBot shield has eight surface mount components, four WS2812B RGB LEDs and four decoupling capacitors. Normally these are pre-soldered but competent solderers looking for a challenge can solder them on the day.

These devices are usually soldered using solder paste and hot air or infrared heating, but they can be soldered using a common soldering iron as well.

'''These steps are completely optional, feel free to get a presoldered shield instead. If you plan to do the SMD assembly please bring some extra tools (described below)'''.

== Parts to Solder ==

As well as the bare SimpleBot Shield PCB, you will need 4 WS2812B RGB LEDs (the large square packages) and 4 "0603" sized 100nF capacitors (the small rectangular packages). All four 100nF capacitors are probably not necessary, you can probably get away with just two or three if need be!

[[File:SimpleBot SMD Components.jpg|400px]]

== Tools Required ==

As well as the components, you will need some special tools for SMD assembly:

* Tweezers for placing components
* Liquid solder flux (flux pens are the easiest form of these).
* Some kind of magnification for checking your work (depending on your eyesight you might need something you can solder under, or just a magnifier you can use afterwards).

[File:SimpleBot SMD Componenents plus tools.jpg|400px]

== Soldering Technique ==

The soldering technique we're going to use is called tack-then-reflow. This means we apply a tiny bit of solder to one pin of each package to hold it in place, then "reflow" solder onto the rest of the pads.

We'll go over the steps of the technique further on, but if you want a preview then [https://www.youtube.com/watch?v=b9FC9fAlfQE&t=6m50s Dave Jones' eevblog covers the technique well in this video].

== IMPORTANT - WS2812B Orientation ==

The WS2812Bs have 4 pads that need to be soldered down, numbered 1 through 4. There is a "pin 1" marking on the board. However, '''the marking on the WS2812B package is not pin 1'''. It is pin 3.

[[File:WS2812B Markings.png]]

So when placing the WS2812Bs, make sure that '''the corner with the triangle marking is diagonally opposite to the pin 1 marking on the board'''.

== Tacking Down ==

I recommend doing an LED and a capacitor at a time, moving from corner to corner.

When each corner is done it will look something like this:
[[File:SimpleBot SMD Soldered corner.jpg|400px]]

Start by flowing a small amount of solder onto just one pad of the capacitor and one pad of the LED, as shown:

[[File:SimpleBot Solder on pads.jpg|400px]]

Don't apply too much solder, use solder wick to take some off if necessary.

In the picture above I've applied solder to two pads on the left side, because I'm left handed. You can use pads on the right side if you prefer.

Next, use tweezers to place the capacitor on top of the pads. Hold the capacitor in place with the tweezers in one hand, and use your other hand to bring the soldering iron in to touch the pad where you already placed some solder. As the pad heats the solder will "reflow" up from the pad onto the end of the capacitor:

[[File:SimpleBot Capacitor One End Soldered.jpg|400px]]

Once the solder cools it "tacks" the capacitor down to the board, so it can't move. Try to bump it with your tweezers, it should stay put.

Repeat the process with the LED - place it on top of the pads, hold it in place with the tweezers in one hand while you heat the pad you presoldered and it solders on to tack it in place. Remember to check the LED orientation before you start soldering!

[[File:SimpleBot LED one pad soldered.jpg|400px]]

If either component is soldered a bit crooked, repeat the process (tweezers in one hand, iron in the other) to reflow the solder and move the component into position. It's important you do this now before you try and solder the other pads!

'''When soldering the LED take special care not to apply too much heat - the green element of the WS2812B is quite heat sensitive and can be damaged if too much heat flows into the LED. You want to remove the soldering iron shortly after the solder becomes molten.'''

== Soldering all pads ==

Now the LED and the capacitor are held firmly in place, we can solder the other pads. This is now a similar technique to through hole soldering, just using a much smaller amount of solder.

Hold the soldering iron in one hand and plain in the other. Go to each unsoldered pad and heat the joint with the iron, then press a small amount of solder into the joint to solder it.

When soldering the LED, the pad is not particularly exposed so some heat needs can be applied via the leg of the LED itself. Try to heat the pad as much as possible, though - go in at a low angle.

Once the remaining pads are soldered, you may want to revisit the first "tacked" pads and apply a tiny bit more solder so they are more firmly attached.

[[File:SimpleBot SMD Soldered corner.jpg|400px]]

In the picture above, there's actually a bit too much solder on most of the pads - but it doesn't matter.

== Solder remaining corners ==

Once the first two components are soldered down, repeat for each corner of the shield.


Once the SMD soldering is done, move on to the [[SimpleBot Shield Assembly]] step.